Avocent LongView LVIPHR Guide de l'utilisateur

590-836-501DLONGVIEW® IP KVM EXTENDERSInstaller/User GuideFor Technical Support:www.avocent.com/support

4 LongView® IP KVM Extenders Installer/User GuideMultiplatform supportThe LongView IP KVM transmitter is connected to the target computer via U

Chapter 1: Product Overview 5Virtual media (not available with LVIPVG-R user station)Mass storage devices, such as removable drives and extern

6 LongView® IP KVM Extenders Installer/User GuideFigure 1.1: LongView IP KVM Extender SystemSafety PrecautionsTo avoid potential video and/or k

Chapter 1: Product Overview 7• If the building has 3-phase AC power, ensure that the workstation and monitor are on the same phase. For best r

8 LongView® IP KVM Extenders Installer/User Guide

9InstallationGetting StartedBefore installing your LongView IP KVM extender system, refer to the list below to ensure that you have all the items nece

10 LongView IP KVM Extenders Installer/User GuideMounting OptionThe user station for each LongView IP KVM extender system mounts to either the

Chapter 2: Installation 11CAUTION: To reduce the risk of electric shock or damage to your equipment, disconnect the power from the user statio

12 LongView IP KVM Extenders Installer/User Guide3. Connect the video connector on the transmitter to the appropriately labeled port on the bac

Chapter 2: Installation 13Figure 2.2: User Station and Transmitter Installation (LongView IP Extender System Shown)Table 2.2: Description of F

USA NotificationWARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s au

14 LongView IP KVM Extenders Installer/User GuideFigure 2.3: User Station and Transmitter Installation (LongView IP VG Extender System Shown)8

Chapter 2: Installation 152 External Power Supply3 Serial Port4 Local Peripherals (attached via PS/2 ports)5 VGA Port6 Speakers7 Microphone8 U

16 LongView IP KVM Extenders Installer/User GuideFigure 2.4: User Station and Transmitter Installation (LongView IP DH Extender System Shown)Ta

Chapter 2: Installation 17Figure 2.5: User Station and Transmitter Installation (LongView IP HR Extender System Shown)Table 2.5: Description o

18 LongView IP KVM Extenders Installer/User GuideTo connect the user station:1. Connect your keyboard, monitor, mouse and other peripheral cabl

Chapter 2: Installation 19Transmitters and user stations may be configured for use on a single subnet or for use across routers. Use of router

20 LongView IP KVM Extenders Installer/User Guide

21OperationsOverviewOperating a target computer through the LongView IP KVM extender system is no different than working directly connected to your ta

22 LongView® IP KVM Extenders Installer/User GuideAccessing the SystemA LongView IP KVM user station will automatically initiate a connection w

Chapter 3: Operations 232. Click the Rcvr radio button to view the system information for your user station.Figure 3.1: User Station Connected

LongView® IP KVM ExtendersInstaller/User GuideAvocent, the Avocent logo and LongView are registered trademarks of Avocent Corporation or its affiliate

24 LongView® IP KVM Extenders Installer/User GuideTo change networking information for the user station and transmitter:1. Press Print Screen a

Chapter 3: Operations 25To change the OSD Timeout:1. Press Print Screen and select the CFG tab.Figure 3.3: Configuration Menu (OSD Timeout)2.

26 LongView® IP KVM Extenders Installer/User Guidevia the transmitter. One password controls access to the user station, the other password con

Chapter 3: Operations 27NOTE: It is recommended that you configure the network settings for the transmitter before you configure the network s

28 LongView® IP KVM Extenders Installer/User Guide5. Press 1 to select the Transmitter Network Config option and press Enter.Figure 3.6: Transm

Chapter 3: Operations 292. Type the password and press Enter. The Receiver Main Menu will appear.Figure 3.7: Receiver Main MenuTo access the N

30 LongView® IP KVM Extenders Installer/User Guide2. Press 2 to select the Transmitter IP Config option and press Enter. The old Transmitter IP

Chapter 3: Operations 31To configure the network settings for the user station:1. Press 1 to select the Receiver Network Config option in the

32 LongView® IP KVM Extenders Installer/User Guide9. Press 6 to select the Network Speed option to toggle between Auto-Negotiate mode (option 1

Chapter 3: Operations 333. Press 1 to select Network Configuration and press Enter. The Network Configuration Menu will appear.4. Press 2 to s

InstructionsThis symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literatur

34 LongView® IP KVM Extenders Installer/User GuideTo change the user station password:1. Press 2 to select Change console password and press En

Chapter 3: Operations 353. Press 2 to access the Security Configuration Menu. You have the option of disabling or enabling the password and ch

36 LongView® IP KVM Extenders Installer/User GuideNOTE: It is recommended that you Flash upgrade the transmitter before you Flash upgrade the u

Chapter 3: Operations 376. Enter the URL for the upgrade file using the following syntax: http://<server ip address>[:server port]/<

38 LongView® IP KVM Extenders Installer/User GuideNOTE: If the LongView IP KVM user station determines that the upgrade file is invalid, the Lo

Chapter 3: Operations 395. During reset, the LongView IP KVM user station will drop the connection to the transmitter. When reset is complete,

40 LongView® IP KVM Extenders Installer/User Guide2. Press 7 to access the Appliance Information menu and press Enter.Figure 3.18: Appliance In

Chapter 3: Operations 41Configuring Video Input SettingsThe LVIP-R and LVIPHR-R user stations are capable of transmitting either digital (DVI)

42 LongView® IP KVM Extenders Installer/User Guide3. Press 1 to access the Target Video Menu and press Enter.Figure 3.21: Transmitter Target Vi

Chapter 3: Operations 43Figure 3.22: Advanced Video Settings Menu4. Enter the number that represents the port to which you wish to set the EDI

iiiChapter 1: Product Overview... 1Introduction ...

44 LongView® IP KVM Extenders Installer/User GuideTo access the Session Retry Menu:1. Press Enter to display the serial menu.2. Press 1 to acce

Chapter 3: Operations 452. Press 8 to access the Console Settings Menu. Your currently selected OSD hotkey sequence is displayed beside menu i

46 LongView® IP KVM Extenders Installer/User GuideUsing the serial menu, you can disable the OSD time-out or change the time-out period to any

Chapter 3: Operations 47NOTE: To ensure that audio operates correctly, configure the user station and the transmitter with identical audio per

48 LongView® IP KVM Extenders Installer/User Guide3. Press 4 to access the Audio Performance Menu and press Enter. This menu shows you the audi

Chapter 3: Operations 494. Press 8 to choose Display Power Saving Mode, then press Enter. The Display Power Saving Mode Menu will appear.Figur

50 LongView® IP KVM Extenders Installer/User Guide

51CHAPTER4Share ModeUsing Share ModeShare Mode allows multiple users (up to eight user stations per transmitter) to share the audio and video of a tar

52 LongView® IP KVM Extenders Installer/User GuideConfigurationShare Mode can be enabled or disabled from the serial menu.To enable or disable

Chapter 4: Share Mode 53To enable Share Mode on the transmitter:1. From the user station’s serial menu, press 2 to access the Transmitter Main

iv LongView® IP KVM Extenders Installer/User GuideResetting the LongView IP KVM Extender System...

54 LongView® IP KVM Extenders Installer/User Guide

55CHAPTER5Advanced OperationsSimple ASCII Manager InterfaceThe LongView IP KVM extender system features a Simple ASCII Manger Interface (SAMI) that al

56 LongView® IP KVM Extenders Installer/User GuideTo access the SAMI Menu:1. From the Receiver Main Menu, press 8 and Enter to access the Conso

Chapter 5: Advanced Operations 57From the Transmitter Main Menu, press 7 and Enter to access the Console Settings Menu. 2. Press 7 and Enter t

58 LongView® IP KVM Extenders Installer/User GuideEnter the get ipaddr command (the response should be resp ipaddr 192.168.13.7).NOTE: In this

59AppendicesAppendix A: Technical SpecificationsNOTE: During the course of this product’s lifetime, modifications might be made to its hardware or fir

60 LongView® IP KVM Extenders Installer/User GuideTypeThree-wire serial interface: RX, TX, GND via 16450-compatible UARTConnectors 9-pin D-Shel

Appendices 61Mass Storage DevicesAll Mass Storage Class devices that use:SCSI mass storage subclassBulk only transfer protocolPrintersTouch s

62 LongView® IP KVM Extenders Installer/User GuideSafety and EMC Approvals and MarkingsUL, FCC, cUL, VCCI, C-Tick, CETable A.2: LVIPDH-T and LV

Appendices 63DC-input current rating 1.1 AOperating Temperature 0° to 35° Celsius (32° to 95° Fahrenheit) Storage Temperature -20° to 60° Cel

1Product OverviewIntroductionThe Avocent LongView® IP KVM extender system, which includes a transmitter and a user station, provides users with a full

64 LongView® IP KVM Extenders Installer/User GuideTable A.3: LVIP-R User Station Product Specifications NetworkEthernet Standard Ethernet IIIP

Appendices 65AC-input current rating 1 AAC-frequency 50/60 HzOperating Temperature 0° to 35° Celsius (32° to 95° Fahrenheit) Storage Temperat

66 LongView® IP KVM Extenders Installer/User GuideVideo Resolution 640 x 350 @ 85 Hz 640 x 480 @ 60 Hz, 72 Hz, 75 Hz, 85 Hz720 x 400 @ 70 Hz (8

Appendices 67Table A.4: LVIP-T Transmitter Product Specifications NetworkEthernet Standard Ethernet IIExtension PortsNumber 1ConnectorsRJ-45C

68 LongView® IP KVM Extenders Installer/User GuideVideo PerformanceVideo Resolution640 x 350 @ 85 Hz 640 x 480 @ 60 Hz, 72 Hz, 75 Hz, 85 Hz720

Appendices 69Appendix B: Factory Default SettingsTable B.1: LongView IP KVM Extender System Factory Defaults LVIP-R, LVIPHR-R and LVIPDH-R Us

70 LongView® IP KVM Extenders Installer/User GuideLVIP-T, LVIPHR-T and LVIPDH-T Transmitters (continued)Password passwordVideo DVI - NormalVide

Appendices 71Appendix C: Technical Support Our Technical Support staff is ready to assist you with any installation or operating issues you e

72 LongView® IP KVM Extenders Installer/User GuideAppendix D: TroubleshootingNo power status light on user station• Verify that the power suppl

Appendices 73ing, check that the display settings for your target computer are set no higher than a resolution of 1280 x 1024 at 60 Hz refres

2 LongView® IP KVM Extenders Installer/User GuideEthernet addressingThe user station and the transmitter are IP-addressable devices, giving you

74 LongView® IP KVM Extenders Installer/User GuidePoor video quality on monitor attached to user station• Reset video by pressing <F11>.•

Appendices 75• Verify that the Ethernet network is fully operational.Transmitter disconnected from DHCP server• Attempt to reconnect to DHCP

76 LongView® IP KVM Extenders Installer/User Guide

License Information 77License InformationThis product includes various software programs that are copyrighted and released under the GNU Gene

78 LongView® IP KVM Extenders Installer/User Guide1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in an

License Information 79redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you

80 LongView® IP KVM Extenders Installer/User Guide

USA NotificationWarning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s au

590-836-501E LONGVIEW® IP KVM EXTENDERS Installer/User GuideFor Technical Support:www.avocent.com/support

Chapter 1: Product Overview 3• The other is a high-speed port that is used for virtual media (mass storage devices) peripheral devices or othe